Видео

What fo you charge an hour?

start at 1:45.

Great explanation. Love it. Thank you.

Seems so simple after seeing it!, thanks

Most often there isn't enough thread on the mandrel to do this

I love the bloopers at the end!

If your arbor happens to have enough length of thread you can double up hole saws, otherwise you need to get one of those "oops" arbors like the Starrett KA19-N

I love that you mentioned the auger. I found out the hard way that they do get really tight. In fact, I couldn’t get it off. I took it to two different hardware stores before one of the gentlemen had to use a vice and a wrench to get it off. I finally bought one of those that you recommended it cost me about 30 bucks, it is worth it!

I am working at Singapore

Nice demo... You could loosen it with just one blow... I need to open philips head screws on my motorcycle engine cover. The screw grooves are slightly stripped on account of multiple tryouts by a screw driver. I have put a lot of WD-40 and some coconut oil on these screws hoping it to get softer. Would multiple strikes with a impact driver help if it does not loosen in one or two strikes? Thanks

This is wrong advice. In this other video a professional explains why: ruclips.net/video/Jn8DR2UkFbQ/видео.html

Another trick is to use washer, fibre washers, a piece or solder wound around the last thread, or the groove works even better.

thank you for the numbers and specially the trick of the percentage calculation

Will this work well with a metal door with a wood core?

If you have two flutes crossing 90 to each other how dose water escape? Wow

Is there a way of checking a tradie is actually qualified.

Thanks, that's a great tip and well explained - Cheers

Awesome video! But when we calculate for the shower wall. Should we add 10 or 20% for each wall or after we calculate the whole shower wall?

how are you gonna know the amount of tiles needed ?

Thanks, saved me lots of time

Thank you heaps for the advice huge time saving.

👍

Great tip thanks mate

Three years on how are you finding it?

Now I know. As a plumber I have cut some horrible holes

This may be a stupid question, but why would anyone put the grooves upwards. Water gonna sit there.

This a great tip thanks, I have one question and that's is there a drill you recommend for this type of job?? Like power?

Informative and motivational video, thank you! Can you tell me what educational course you did to prepare for your new handyman career. I'm in Australia also.

a great video and very very helpful

Grooves down smooth up.... grooves up always gathers water plus water will leave boards at first groove underneath..... plus grooves up collects muck.....

This was so helpful. Thank you for actually giving full instructions.

Brilliant and so simple ... thanks

An impact driver is a gun a impact screwdriver is what you have in your hands

Was helpful. Thanks

i think its easier to divide the length of the room to the length of the tile and width of the room to the width of the tile then multiply your answer

Thanks for this amazing video but please, how did you come by 1.2 for ten percent wastage and 1.3 for 30 percent wastage?

Nice video mate.

great video just starting to finish my outside stairs that my dad will never finnish hope ill do a decent job this video really helps out

Sorry if I missed this info in the video, but what sort of cement did you use in the grout mix to match the sandstone? I'm not sure what cement to use to get a sand stone coloured grout (I know it's not a standard cement mix). Appreciate your help.

you can also take the hole saw bit out put the larger bit on and then put the older one back in and use it as the arbor

This is not telling me how many 12”x12” squares I need to tile a kitchen backsplash behind the sink

Hi... I was looking for a High Modulus for my bath/shower. I wandered over the street and I was lowered and beheld... I found a Arbosil HM High Modulus Sealant unopened in the street. (My neighbor but two is a Handy Guy.) I got it as it must have fell out his van and he didn't notice. I cleaned it up the next day. I will use this when I fill the bath/shower with water then use it as with the load of water or a person it will be in it. Fill the bath before you put the sealant on to allow the weight of you showering. Otherwise it will just split.

Use a a pedal drill mix up the grouch make saw it's flexible grouch mix up like cream and when you're grouting two square meters at a time and then wash it off 👍 looks to me on your video you're wash off too early that will cause the joints to sink 👎

Ridiculously simple. Why couldn't I work this out?

I have some sandstone tiles with some really strange stains which I can’t explain. I’ve bleached, I pressure washed, I’ve ground sand into them. I was wondering how I can get a new surface?

what kind of wood was that

Mine does not screw in the same way? Thank you! My saws don’t have those pin holes either!

Our pool man put sandstone tiles around our salt pool, it was sealed 3 times but the salt water is eating away the tiles.Do you have any idea what we can do

Very helpful, now what about the entry door ? Did you calculate that as well like the window?

Hi, we need mould when we embossed with temperature.. which is the best